Search results for 'beretta'

Beretta 92 Mec-Gar Magblock 10/18 (9mm) 10 Round Limiter

This Magblock fits the Mec-Gar Beretta 92 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on Mec-Gar (M9) Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #15 and glue flush at the bottom for 10/18 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #15 will show in the limiter window notch like in the photos. 

Beretta 81 Magblock 10/12 (.32) 10 Round Limiter

This Magblock fits the factory Beretta 81, 81B, 81BB 12 round .32 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/12 Beretta 81 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 81 magazines as shown in the photos. Other types of magazines may require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to "7" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Beretta 96FS MecGar Magblock 10/13 (.40) 10 Round Limiter

This Magblock fits the MecGar Beretta 96FS 13 round magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta 96FS magazines.
- Save time and money and keep your magazines legal. 
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" MecGar 96 magazines as seen in the photos.

*If using our Universal Limiter for this magazine: Cut to #8 and glue flush at the bottom for 10/13 limiter. Slide lock is not used. When epoxy cures assemble magazine. #4 will show in the limiter window notch like in the photos. 

Beretta M9-22, 92FS-22, M9A1-22 (.22LR) Magblock 10 Round Limiter New Improved Fit

- Fits 15 round .22 Beretta 92-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Beretta PX4 Full Size Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. A notch allows room for the metal tab on the locking plate. It is held in place with spring tension alone or can be glued or epoxied if desired. (Compact magazines use a different limiter)

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 magazines as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #17 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

Beretta APX Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #15 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #15 will show in the limiter window notch like in the photos. 

Beretta PX4 Full Size Magblock 10/20 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 20 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. It is held in place with spring tension alone or can be glued or epoxied if desired. 

- Save time and your expensive factory magazines. Quick install to make 10/20 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 20 round Beretta PX4 magazines as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #24 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

Beretta APX Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 21 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/21 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #24 and glue flush at the bottom for 10/21 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #24 will show in the limiter window notch like in the photos. 

Beretta APX Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 15 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #14 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #14 will show in the limiter window notch like in the photos. 

Beretta 92FS Magblock 10/20 (9mm) 10 Round Limiter for MecGar 20 Round Magazines.

This Magblock fits the MecGAr Beretta 92FS (20 round) 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/20 MecGar Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on MecGar Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

Beretta APX Magblock 10/18 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 18 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #20 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #20 will show in the limiter window notch like in the photos. 

Beretta APX Compact Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX Compact 13 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta APX Compact magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX Compact magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #4.5 and glue flush at the bottom for 10/13 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #4.5 will show in the limiter window notch like in the photos. 

Beretta ARX160 22LR 10/30 Magblock 10 Round Limiter

- This block will convert 30 round Beretta ARX160 22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

Beretta APX Magblock 10/15 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 15 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #9 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #9 will show in the limiter window notch like in the photos.