Search results for 'p226'

Magblock 10 Round Limiter for MecGar Sig P228 15 Round Magazines

- Fits 15 round 9mm MecGar Sig P228 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for MecGar Sig P228 18 Round Magazines 

- Fits 18 round 9mm MecGar Sig P228 magazines with the +3 extension. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig 15 Round P229-1 Magazines. 
Fits the Sig P228 M11-A1

- Fits the new 15 round 9mm Factory Sig P229-1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig 15 Round P228 M11-A1 and P229-1 Magazines. 
Fits the Sig P228 M11-A1

- Fits the new 15 round 9mm Factory Sig P228 M11-A1 and P229-1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig P229 and P226  12 Round .40 Magazines. 

- Fits the new 12 round .40 Factory Sig P229 and P226 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig P227 (.45) 14 Round Magazines

- Fits 14 round .45 Sig P227 magazines.  (13+2 extension)
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Sig P228 13 Round Magazines

- Fits 13 round 9mm Factory Sig P228 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig P320 (.40) 13 Round Magazines

- Fits 13 round .40 Sig P320 factory magazines.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
  *** *Compatibility Note: This is the same block as a Sig P228 9mm 10/13 Limiter and may be marked as such***

Magblock 10 Round Limiter for Sig P229 and P226  12 Round .40 Magazines. 

- Fits the new 12 round .40 Factory Sig P229 and P226 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
-*Same as CZ 10/12 limiter and likely marked as "CZ".

Promag Sig Sauer P226 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Promag Sig P226 15 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/15 Promag Sig Sauer P226 magazines. 
- No modification to the magazine is required.
-  Lightweight and will not interfere with magazine reliability.
- Tested on Promag Sig P226 magazines as shown in the photos. The block may need to be modified to work with magazines from other manufactures. 

Note: This block is designed for the Promag Sig P226 15-Round Magazines only.

Sig Sauer P226 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Sig P226 15 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/15 Sig Sauer P226 magazines. 
- No modification to the magazine is required.
-  Lightweight and will not interfere with magazine reliability.
- Tested on factory Sig P226 magazines as shown in the photos. The block may need to be modified to work with magazines from other manufactures. 

*This magazine is known to use two different types of followers depending on where they were manufactured. Please select the country of manufacture or your follower length below. The most accurate way is to measure your follower as shown in the photos. 

Magblock 10 Round Limiter for Sig P226 (.40) 13 Round Magazines

- Fits 13 round .40 Sig P226 magazines made by Mec-Gar. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
  *Universal Limiter can be used to make this block. Cut the base flush with #8 showing in the indicator notch. 

Magblock 10 Round Limiter for Sig P226 (.40) 15 Round Magazines

- Fits 15 round .40 Sig P226 magazines made by Mec-Gar.  (13+2 extension)
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig P226 18 Round Magazines

- Fits 18 round 9mm Sig P226 magazines made by Mec-Gar. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*This Limiter can be made using the Universal Pistol Limiter by cutting flush at the base with #16 in the indicator notch. 
*The product sold at this link is pre-cut and fixed at this length. 

* This block will work in the Tisas Zigan 9mm Mecgar 18-round magazine.