Search results for 'magnet'
-
FAL 10/30 Magblock
Converts FAL 30 round magazines to 10 rounds.
This block will fit FAL 30 round magazines and convert them to 10 rounds.
The end of the magazine spring will snap into the hole in the block to hold it in place.Tested in DSARMS manufactured 30 round magazines, but should work in other similar magazines.
$6.59 As low as: $4.95 -
Epoxy Machinable- Fast Set
Epoxy, Machinable Fast Setting.
Hardman Double Bubble Pouch (3.5 grams). Will work for a few rifle or up to 10 pistol limiters depending on amount used. Features a longer working time than the Red fast set epoxy:
- Starts to set in 25 minutes, Handling time 4 hours. Mix small batches if doing a lot of limiters.
- Handling strength: 4 hours.
- Color: Aluminum.
- Viscosity: Honey.
- Full Strength: 24 hours 3.5 Grams.$4.09 As low as: $3.89 -
Glock .45 Follower G21
Glock .45 OEM Replacement Follower
Replacement Glock .45 follower which is compatible with Magblock Limiters
- Fits Glock 21 and other .45 Glock Magazines.
$4.95 -
Sale
Large 6" Flush Cutters
Larger 6" Flush cut pliers make easy work of cutting through the Universal Limiters, Glock, XD/XDM, and Pmag limiters. Can cut universal limiters flush with the base, but may take a cut on each side to get through.
Regular Price: $13.95
Special Price $10.95
-
Magblock Universal Pistol Base
Magblock Universal Pistol Base only
$6.25 As low as: $5.49 -
Patch MagazineBlocks.com Round
Great for the range bag and to show your magazines are blocked.
Also for patch collectors like myself :)
- 3” Round PVC
- Hook and loop backing
$4.95 -
Sale
Large 6" Flush Cutters
Flush cut pliers make easy work of cutting through the Glock, XD/XDM, Universal and Pmag limiters. Can cut universal limiters flush with the base.
Good for detail work.
Regular Price: $13.95
Special Price $10.95
-
Walther UZI Magblock (.22LR)
Walther UZI (.22LR) Magblock 10 Round Limiter
- Fits 20 round Walther UZI .22 magazines.
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.$6.59 As low as: $5.95 -
Sale
10 Block Bulk Pack
10 Block Bulk Pack
- 10 block bulk pack. Includes ONLY the following: Pmag M2/MOE 10/30, Pmag M2/MOE 10/20, USGI 10/30, and USGI 10/20, HK G36, XD/XDm 9 and .40 Pistol blocks, and Glock 9 and .40 Pistol blocks, excluding the Glock 10/33.
- You MUST specify the quantity and type of each block below. Please be specific.
Excludes 10/20 Colt blocks and Gen 3 blocks
Regular Price: $45.00
Special Price $39.95
-
Magpul Ranger Plate 223
The Magpul PMAG Ranger Plate is a floorplate replacement for the 5.56x45 PMAG and EMAG.
The ranger plate incorporates an integral loop similar to the original Magpul USGI Ranger.
When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.
Made in U.S.A.
$5.95 -
Magblock Universal Pistol Shaft
Magblock Universal Pistol Shalf only
$6.25 As low as: $5.49 -
Suomi 10/36 Magblock
Limits 36 round Suomi magazines to 10 rounds.
New design does not replace the difficult to remove lower floor plate but instead rests on top of it.
The spring can also be epoxied to the block which allows for disassembly and cleaning.
Easy and simple way to make 10/36 Suomi magazines without damaging your hard to find magazine.
$6.25 As low as: $4.75 -
Glock Follower 9mm
Glock Follower (9mm) Replaces #4,5,6, & Gen 4
Replacement Glock 9 mm follower which is compatible with our Magblocks.
-Replaces #4,5,6, and Gen 2,3 and 4 magazine followers in 9 mm.
$4.95 -
M14 -M1A Blocks
Fits M14/M1A 7.62x51mm/.308 20 round magazines.
- Easiest and quickest way to make a 10 round M14 Magazine.
- Can be permanently attached to the spring with epoxy.
- The block attaches to the spring to prevent noise and movement.
- No magazine modifications required.
-Allows loading on a closed bolt with 10 rounds installed.
-New light weight design.
* Will work in new Springfield 20 Round M1A magazines.
$6.50 As low as: $5.95 -
Epoxy Fast Setting
Epoxy Fast Setting
Hardman Double Bubble Pouch (4.0 grams). Will work for a few rifle or up to 5-10 pistol limiters depending on amount used. Features:
- Starts to set in only 3- 5 minutes. Mix small batches if doing a lot of limiters.
- Handling strength: 15-30 minutes.
- Color: white.
- Viscosity: honey.
- Full Strength: 24 hours 4.0 Grams.$3.95 As low as: $3.79