Taurus G2C Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus G2C 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus PT111 G2 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

Bersa Thunder Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Bersa Thunder 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder 9mm magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/17 Bersa Thunder High Capacity magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "16" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Smith & Wesson SD9 VE 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm SD9VE, SD9G, SD9E, SD9P, SD9V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 17 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #16 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

Ruger American 10/17 Magblock 10 Round Limiter for 17 Round Magazines

This Magblock fits the Ruger American Pistol  9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger American Pistol Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "18" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

Beretta APX Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #15 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #15 will show in the limiter window notch like in the photos. 

MagBlock Essentials First Aid Kit 

-This kit contains everything needed when you are having a bad day

-This kit has been designed to allow for quick access to your lifesaving gear when you need to most

 -All items are sealed and come packed in a Quick Release Medical Pouch

-This kit would be a great addtiion to a range bag, battle belt, and/or a truck

-North American Rescue items come packed and sealed and come from NAR

-North American Rescue Cat Gen 7 Tourniquet is factory and not a knock-off

ETS Glock .45 Magblock 10 Round Limiter for 40 round Magazines

This Magblock fits the ETS 30 round .45 magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/30 Glock .45 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

Glock 19 (9mm) Magblock (For Older Style Followers Only)

- Fits 15 round 9mm Foctory Glock 19 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits older style follower Glock Magazines only.
Only compatable with the follower type shown in the pictures. 

Shield Arms Glock 43X and Glock 48 (9mm) Magblock

- Fits Shield Arms 15+2 round for Glock 43x and Glock 48.
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Note: This block will work in Gen 1, Gen 2, and Gen 3 magazines.

Glock 17 and Glock 34 (9mm) Magblock

- Fits 17 round 9mm Factory Glock 17, Glock 19X and Glock 34 magazines.  *See details on correct follower types below. 
-Will also fit Korean Glock Magazines.  
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures. 

New patent pending design allows this limiter to be adapted to fit all other Glock 9mm and .40 magazines including a 15 round option for the Glock 17 magazine. Cutting using an appropriate tool is required. Pre-cut limiters are available.

Magblock 10 Round Limiter for Pmag 17 GL9 Magazines.

- Fits 17 round Magpul Pmag GL9 magazines for Glock 17 and Glock 34

- Easy installation at the base of the magazine and sits on top of the locking plate.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits Magpul Pmag 17 GL9 Magazines Only. Will not fit Glock Brand Magazines.

Magblock 10 Round Limiter for Shadow Systems MR920 Series Magazines.

- Fits 15 round Magpul Pmag GL9 magazines for Shadow Systems MR920.

- Easy installation at the base of the magazine and sits on top of the locking plate.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits Magpul Pmag 15 GL9 Magazines Only. 

Universal Limiter Instructions: To make this limiter using the universal pistol limiter, cut the base flush with #8 showing in the indicator notch. Then cement base and slide in place. The bottom lock is not used. 

Magblock 10 Round Limiter for Pmag 15 GL9 Magazines.

- Fits 15 round Magpul Pmag GL9 magazines for Glock 19.

- Easy installation at the base of the magazine and sits on top of the locking plate.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits Magpul Pmag 15 GL9 Magazines Only. Will not fit standard Glock type Magazines.

Universal Limiter Instructions: To make this limiter using the universal pistol limiter, cut the base flush with #8 showing in the indicator notch. Then cement base and slide in place. The bottom lock is not used. 

Note: This block will fit the New Shadow Systems MR920 15 round magazine.

ETS Smith & Wesson M&P Full Size 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm ETS M&P magazines. 
- New design installs into the follower like in the pictures.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with ETS S&W Magazines.

-This block is for the ETS S&W M&P 9mm 17-round magazine only.