Search results for '10'

Saiga 10/30 Magblock 

- Converts the Saiga .223 Surefire 30 round magazine to 10 rounds.

- This block fits the Saiga polymer 30 round magazines in .223/5.56mm.

- This block will replace the original magazine locking plate.

- Fits  Surefire (SGM) magazines. Others may need modification for a correct fit.

AK-74 Magblock for 5.45x39mm 30 round magazines

• This AK-74 block fits most 30 round polymer 5.45x39 mm magazines and will convert them to hold only 10 rounds.
• The new design features a spring catch which will allow an easy attachment point to the spring.
• This prevents the block making noise and epoxy can be added at this point to make it permanent.
• This block will replace the original magazine locking plate.
• Marked where to cut for a 15 round limiter. 

Tested on the following AK74 magazines with perfect function:
Tapco, Circle 21, Izmash, and East German Bakelite.  Will likely fit other similar magazines. Let us know and we will update the list. 

Tapco AK47 10/20 Magblock

This block fits the Tapco 20 round AK47 magazines and will convert them to a 10 round magazine.

-Replaces the lower locking plate.

-Works on Tapco 7.62x39mm 20 Round AK magazines.

Converts FAL 20 round magazines to 10 rounds.

This block will fit surplus military FAL 20 round magazines and convert them to 10 rounds.
The end of the magazine spring will snap into the hole in the block to hold it in place.

Magblock 10 Round Magazine Capacity Limiter for Thermold 15 and 20 round AR-15/M16 Magazines.

- Will convert both a 20 or 15 round magazine to hold only 10 rounds.

- Only fits current production Thermold magazines. Has not been tested on older versions. Some modification may be needed for older production magazines. 
- The Thermold 15 and 20 round magazines use the same body size and differ only by a slight internal modification. The same limiter will limit both magazines to 10 rounds. 

10 Round Limiter for CAA Indicative 30 Round Polymer Magazines

Magblock 10/30 MCL (Magazine Capacity Limiter) for CAA 30 round polymer magazines in .223/5.56mm. 

- This block will attach to the bottom of the spring, and sits on top of the original locking plate.
- Easy conversion of 30 round CAA magazines to hold 10 rounds.
- Does not affect reliability.
- No increase in spring pressure. 

Magblock 10/30 MCL (Magazine Capacity Limiter) for Thermold 30 round AR-15/M16 Magazines.

Magblock for ArmaLite AR10 20 Round Magazines.  10 and 15 Round Limiters.

Fits ArmaLite AR10  .308/7.62x51mm 20 round magazines and will convert them to hold either 10 or 15 rounds.

- Easy to install in seconds.
- No need to drill any holes.
- Load magazines on a closed bolt in most rifles.
- No external magazine modifications required.

New lighter, more reliable design is made from abs plastic.

Magblock 10 Round Limiter for Sten 32 and 20 Round Magazines

- Fits Sten 32 round magazines and 32 round magazines that have been "Brass Wire" limited to 20 rounds. You must choose an option below.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.
- Made of a super strong, heat resistant, fiber reinforced polymer.
- Please Note: The Photos show a 32 round magazine that has 2 brass wires on the inside that protrude outside near the bottom of the magazine. This is a Sten 32 round magazines that was limited to a single stack 20 round magazine. This was a common military modification that helped with reliability and very widespread on surplus magazines. Please select the "Single Stack Modified" option below if you see these brass wires at the bottom of your magazine to ensure you receive the proper limiter. Thank you.

Converts FAL 30 round magazines to 10 rounds.

This block will fit FAL 30 round magazines and convert them to 10 rounds.
The end of the magazine spring will snap into the hole in the block to hold it in place.

Tested in DSARMS manufactured 30 round magazines, but should work in other similar magazines.

Magblock for IO Inc. or Inter Ordnance AK47 (7.62x39mm) Magazines.

- This block fits the 30 round AK47 magazines in 7.62x39mm made by IO and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

10 Round Limiter for MSAR 30 Round Polymer Magazines

Magblock 10/30 MCL (Magazine Capacity Limiter) for MSAR 30 round polymer magazines in .223/5.56mm.

- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.

- Customized base of the Magblock includes one locking point.

- Does not affect reliability.

- No increase in spring pressure.

AR10 Magblock 5/10

Fits ACS and C-Products .308/7.62x51mm 10 round magazines and will convert them to hold only 5 rounds.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

- May fit other brand AR 10 Magazines. 

Ruger BX-25 Magblock 10 Round Limiters

- Fits 25 round 22LR Ruger BX25 magazines.
- Easy installation.
- Limits the magazine to 10 rounds of 22LR
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.