Search results for 'beretta'

Beretta 90-Two Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 90-Two 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 90-Two magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92 17 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

 Attention: Make sure to verify what magazine you have before ordering. The magazine you have should look like the one in the picture. 

Beretta PX4 Full Size Tactical Magblock 10/17 (.40) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round .40 caliber magazines and will limit them to 10 rounds. Installs at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired. (This block is for the tactical version magazine).

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines in .40S&W.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 (.40) magazines as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #19 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

Beretta M9-22, 92FS-22, M9A1-22 (.22LR) Magblock 5 Round Limiter New Improved Fit

- Fits 15 round .22 Beretta 92-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 5 rounds of .22 for hunting. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Genuine Factory Beretta 92FS Magblock 10/18 (9mm) 10 & 15 Round Limiter

This Magblock fits the factory Beretta 92FS Series 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta 92 Series magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92FS 18 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/18 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

 Attention: Make sure to verify what magazine you have before ordering.This block will fit the following 18-round 92FS series magazines:

Beretta 90-two, Beretta 92G, Beretta M9, Beretta 92D, Beretta 92 Vertec, Beretta 92F

Beretta 80X Magblock 10/13 (.380) 10 Round Limiter

This Magblock fits the factory Beretta 80X 13 round .380 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta 80X magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 80X magazines as shown in the photos. Other types of magazines may require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between numbers 4 to 5 showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done.