Sig Sauer 1911 (.22LR) Magblock 10 Round Limiter 

- Fits 12 round .22 Sig Sauer 1911 magazines. 
- Easy installation. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Magblock 10 and 15 Round Limiter for Rock Island Armory/Armscor A2 1911 Double Stack 17 Round 9mm Magazines

- Fits 17 round +2 extension (See pictures for details) 9mm RIA A2 1911 Double Stack magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Sig P226 19 Round Mec-Gar Magazines

This Magblock fits the Sig P226 X-Five Mec-Gar 19 round magazines (With aluminum addition as shown) made by Mec-Gar and will limit them to 10 rounds.

- Easy installation at the base of the spring.

- Limits the magazine to 10 rounds of 9mm.

- Held in place with spring tension or can be epoxied for a permanent modification.

- Lightweight, efficient design.

- Made of a super strong, heat resistant, fiber reinforced polymer.

Block used is a Universal Pistol Limiter cut to #21.

AREX Rex Zero 7.65 Magblock 10 Round Limiters 

- Fits 18 round 32acp Factory AREX Rex Zero 7.65 magazines as shown.
- Tested in AREX Rex Zero 7.65 18 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 7.65 (.32acp)
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 19 shown in the indicator notch with the sides and front of the base sanded. Cement together after testing fit. 

Note: This block has only been tested with magazine that has the spring bunch at the bottom.

Smith & Wesson 5900 Series Magblock 10/14 (9mm)

This Magblock fits the Smith & Wesson 5900 Series 14 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds under the magazine follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/15 S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

-Block is designed for the 14 round, black follower, early version, 659 series magazines. 

Magblock 10 Round Limiter for Remington 1911 R1 9mm magazines

- Fits 18 round 9mm Remingto RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Promag Bersa Thunder Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the Promag Bersa Thunder 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder 9mm magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/17 Promag Bersa Thunder High Capacity magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original Promag Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "19" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Springfield XDM Elite 10mm Magblock 10 Round Limiter

• Fits 16 round XDM Elite 10mm magazines. 
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of 10mm
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 
• NOTE: (Same limiter as the XDM 9mm 10/19, just cut down)

Magblock 10 Round Limiter for Remington RP9 9mm magazines

- Fits 18 round 9mm Remingto RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington RP9 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

ETS Glock 9mm Magblock 10 Round Limiter for 31 round Magazines

This Magblock fits the ETS 31 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/31 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

ETS Glock .40 Magblock 10 Round Limiter for 19 round Magazines

This Magblock fits the ETS 19 round .40 magazines for Glocks and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/19 Glock .40 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

 *This block is designed for the ETS Glock .40 19 round magazine only. If used in other magazines it might need to be modified. 

Magblock 5 Round Limiter for Pmag 10 GL9 Magazines.

- Fits 10 round Magpul Pmag GL9 magazines for Glock 19.

- Easy installation at the base of the magazine and sits on top of the locking plate.
- Limits the magazine to 5 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits Magpul Pmag 10 GL9 Magazines Only. Will not fit standard Glock type Magazines.

Universal Limiter Instructions: To make this limiter using the universal pistol limiter, cut the base flush with #6 showing in the indicator notch. 

AC-Unity Glock 19 (9mm) Magblock

- Fits 15 round 9mm AC Unity Glock 19 Magazines.  
- Easy installation at the base of the magazim.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

ETS Glock 9mm Magblock 10 Round Limiter for 15 round Magazines

This Magblock fits the ETS 15 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/15 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

ATTENTION: This block is designed for the ETS Glock19 15 round magazine only.