Smith& Wesson

Smith & Wesson M&P Full Size 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm M&P magazines. 
- Will also fit 2.0 models
- Also reported to work with full frame magazines limited to 15 rounds that have extra spring coils at the base of the magazine. (see photos)
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W Magazines.

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

*Universal Pistol Limiter Instructions: Cut to #14 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #14 will show in the limiter window notch like in the photos.  

*Note: This block will work in the new M&P 2.0 Metal Series Pistols that come with 17rd magazines.

Smith & Wesson CSX 9mm Magblock 10 Round Limiters

- Fits 12 round 9mm CSX magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 12 Round CSX Magazines. 

Smith & Wesson M&P 2.0 10mm Magblock 10 Round Limiters

- Fits 15 round 10mm M&P magazines. 
- Limits the magazine to 10 rounds of 10mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W Magazines M&P 10mm

-This block will fit standard, 2.0, and Performace Center 15-round 10mm magazines

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

Smith & Wesson 5900 Series Magblock 10/14 (9mm)

This Magblock fits the Smith & Wesson 5900 Series 14 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds under the magazine follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/15 S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

-Block is designed for the 14 round, black follower, early version, 659 series magazines. 

Smith & Wesson M&P Shield Plus, Equalizer 9mm Sub-Compact Magblock 10 Round Limiter

- Fits 13 round 9mm M&P Shield Plus magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

ProMag 1911  .45 Magblock

• Fits 15 round ProMag 1911 .45 magazines. 
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of .45
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

Smith & Wesson 4006, 4046, 4043 Magblock 10 Round Limiters

- Fits 11 round .40 4006, 4046, 4043 magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 4006 magazine.

Magblock Universal Pistol Limiter 3 Pack Kit
Allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

Save time and money by making your magazines legal. 

NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut.  Now you have an option if we do not have a limiter available for your specific magazine with the recent law changes. If they don't work out for you just send them back for a refund or exchange.

- This Magblock fits most magazines from .380, 9mm, .40, 10mm and .45 magazines.

- Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use. Highly recommend using optional Magblock Cement below.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. 

Refrence page. Lengths for tested magazines: http://www.magazineblocks.com/universal

Smith & Wesson SD40 VE .40 Magblock 10 Round Limiters

- Fits 15 round .40 SD40VE, SD40G, SD40E, SD40P, SD40V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40 cal. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 15 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #12 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #12 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

Sig Sauer 1911 (.22LR) Magblock 10 Round Limiter 

- Fits 12 round .22 Sig Sauer 1911 magazines. 
- Easy installation. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Smith & Wesson M&P Shield Plus, Equalizer 9mm Magblock 10 Round Limiter

- Fits 15 round 9mm M&P Equalizer/Shield Plus magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Smith & Wesson M&P Five-Seven Magblock 10 & 15 Round Limiter

- Fits 22 round 5.7 mm S&W M&P 5.7 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

MagBlock Essentials First Aid Kit 

-This kit contains everything needed when you are having a bad day

-This kit has been designed to allow for quick access to your lifesaving gear when you need to most

 -All items are sealed and come packed in a Quick Release Medical Pouch

-This kit would be a great addtiion to a range bag, battle belt, and/or a truck

Smith & Wesson SD40 VE .40 Magblock 10 Round Limiters

- Fits 15 round Promag .40 SD40 magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40 cal. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with Promag S&W 15 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #12 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #12 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

This block is design for Promag S&W SD40 magazine only.