Shopping Cart - $0.00

You have no items in your shopping cart.

 
Return to Previous Page

Smith& Wesson

10 round limiters for Smith & Wesson M&P and other popular pistol magazines. Due to the design of the M&P followers these magazines are difficult to limit to 10 rounds, but we have found a solution. the Magblock 10 round limiter for the S&W M&P is now available.
Set Descending Direction

Grid List

  1. S&W M&P 10/17 Magblock 10 Round Limiter

    Smith & Wesson M&P 9mm Magblock (10 and 15 Round Limiters)

    Smith & Wesson M&P 9mm Magblock 10 and 15 Round Limiters

    - Fits 17 round 9mm M&P magazines. 
    - New design installs at the base of the spring.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. - Tested with factory S&W and Promag Magazines.

    *Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

  2. S&W 5906 10 Round Magazine Capacity Limiter

    Smith & Wesson 5906 Magblock 10/15 (9mm)

    Smith & Wesson 5906 (9mm) Magblock 10 Round Limiter

    - Fits factory 15 round 9mm 5906 magazines. 
    - Easy installation under the magazine follower.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 

    *Please click on photos for installation instructions. 

  3. S&W M&P 10/15 Magblock 10 Round Limiter Installed. This was a difficult design due to the follower shape. The block is installed between the gap in the spring. If it does not sit like in the photo then re-install the spring from the other side of the foll

    Smith & Wesson M&P Magblock 10/15 (.40)

    Smith & Wesson M&P .40 Magblock 10 Round Limiter

    - Fits 15 round .40 M&P magazines. 
    - Easy installation under the magazine follower. See instructions below and photos.
    - Limits the magazine to 10 rounds of .40 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 

    *Please click on photos for installation instructions. 

  4. S&W M&P 10 Round Limiter for 12 Round 9 mm Magazines.

    Smith & Wesson M&P Magblock 10/12 (9mm Compact)

    Smith & Wesson M&P 9 mm Compact Magblock 10 Round Limiter

    - Fits 12 round 9mm M&P magazines. 
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of 9 mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 

    **Note: This is the same limiter as the CZ 10/12 and may be marked "CZ". See photos for install instructions.

  5. Fast Set Epoxy

    Epoxy Fast Setting

    Epoxy Fast Setting


    Hardman Double Bubble Pouch (4.0 grams). Will work for a few rifle or up to 5-10 pistol limiters depending on amount used.
    Features:
    - Starts to set in only 3- 5 minutes. Mix small batches if doing a lot of limiters.
    - Handling strength: 15-30 minutes.
    - Color: white.
    - Viscosity: honey.
    - Full Strength: 24 hours

    4.0 Grams.
    $2.39
  6. Machinable Yellow Pouch Double Bubble Epoxy

    Epoxy Machinable- Fast Set

    Epoxy, Machinable Fast Setting.


    Hardman Double Bubble Pouch (3.5 grams). Will work for a few rifle or up to 10 pistol limiters depending on amount used.
    Features a longer working time than the Red fast set epoxy:
    - Starts to set in 25 minutes, Handling time 4 hours. Mix small batches if doing a lot of limiters.
    - Handling strength: 4 hours.
    - Color: Aluminum.
    - Viscosity: Honey.
    - Full Strength: 24 hours

    3.5 Grams.
    $2.39
  7. Installation of the S&W M&P-22 10 round limiter is simple. Just replace the 12 round locking plate with this custom 10 round locking plate.

    Smith & Wesson M&P22 Magblock 10/12 (.22LR)

    Smith & Wesson M&P22 (.22LR) Magblock 10 Round Limiter

    - Fits 12 round .22 M&P-22 magazines. 
    - Easy installation by replacing the locking plate. See photos.
    - Limits the magazine to 10 rounds of .22 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 

    *Please click on photos for installation instructions. 

  8. MagazineBlocks New Adjustable Universal Pistol Limiter.

    Magblock Universal Pistol Limiter Kit

    Magblock Universal Pistol Limiter kit allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

    NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut. This is a new release product that does not come with any instructions or packaging at this time. A YouTube video is available. We just want to give people the option to use them if we do not have a limiter available for your specific magazine yet with the recent law changes. If they don't work out for you just send them back for a refund minus shipping charges.

    - This Magblock fits many magazines from .380, 9mm, .40, and some .45 magazines.

    - Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use.

    - Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

    - Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower/.

    - No modification to the magazine is required.

    - Lightweight and will not interfere with magazine reliability.

    - Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. We do offer these as an option for some magazines already precut.

    *If you are a return customer and know the exact length needed we can pre-cut them for you. You must know the number that shows in the limiters indicator notch when the adjustable part is flush with the base. See photos on where the notch indicator is found if you are not sure.

Set Descending Direction

Grid List