Shopping Cart - $0.00

You have no items in your shopping cart.

 
Return to Previous Page

Magblocks

Magazine Capacity Limiters also known as Magblocks for multiple rifles and pistol magazines.

Set Descending Direction

Grid List

Page:
  1. 3
  2. 4
  3. 5
  4. 6
  5. 7
  1. Installs at the base of the magazine. Can be epoxied or the floor plate glued closed for a permanent modification.

    Sig Sauer P320/P250 Magblock 15/17 Limiter (9mm)

    - NOTE: This is the same product as the Sig P229 .40 10/12 limiter and may be marked as such.

  2. PMAG MCL 5/30 Block (5 Round Limiter)

    PMAG 5/30 Magblock (5 Round Limiter)

    Magblock 5/30 (5 Round Magazine Capacity Limiter) 

    This block is for use in Magpul 30 round Pmags. Both Gen 2 and M3. These blocks will replace the lower spring attachment point (locking plate) and convert a 30 round magazine to hold only 5 rounds where required for hunting. Note: This is a custom made limiter, not like the other injection molded Pmag limiters.

  3. Same as M14 M1A Block shown installed in LaRue magazine.

    LaRue Tactical 10 Round Limiter for 20 Round 7.62 Magazines Magblock (.308) 10/20 Limiter

    Magblock for the LaRue Tactical 20 round AR-10 Magazines. Made of heat and impact resistant fiber reinforced polymer. Won't deform even in the most hostile environments. This is the same as the M14 Limiter. Will be a tight fit in the base. Thanks to EBR Works for this compatibility update. Check them out at for compliance work:  http://www.ebrwebstore.com/middleman-ffl-services

  4. Magblock 10 Round Limiter for the Walther P99 M2 15 round 9mm magazines.

    Walther PPQ M2 9mm Magblock 10/15 (10 Round Limiter)

    Walther PPQ M2 Magblock 10 Round Limiters

    - Fits 15 round 9mm Factory Walther PPQ M2 magazines as shown.
    - Tested in M2 version PPQ Magazines.
    - Easy installation at the base of the spring as shown.
    - Limits the magazine to 10 rounds of 9mm
    - Held in place with spring tension or can be epoxied for a permanent modification.
    - Lightweight, efficient design.

    Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

  5. Sig P229/226 .40 Magblock 10 round limiter for 12 round magazines.

    Sig Sauer P224 (9mm) 10/12 Magblock

    Magblock 10 Round Limiter for Sig P229 and P226  12 Round .40 Magazines. 

    - Fits the new 12 round .40 Factory Sig P229 and P226 magazines. 
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of .40 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 
    - Made of a super strong, heat resistant, fiber reinforced polymer.

  6. CZ-75 Tactical Sport 10 round limiter for 20 round magazines. Installs at the base of the spring.

    CZ-75 Tactical Sport 10/20 Magblock (9mm)

    CZ-75 Tactical Sport 10/20 Magblock 10 Round Limiter for 20 Round factory magazines

    This Magblock fits the CZ-75 Tactical Sport 20 round magazines will limit them to 10 rounds. Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

    - Simple install to make 10/20 CZ-75 magazines.

    - No external modification to the magazine is required.

    - Lightweight and will not interfere with magazine reliability.

    NOTE: Universal Limiter Instructions: Indicator notch should show "24" which is the maximum length, the base is flush.

  7. Magblock epoxy cement

    Magblock Epoxy Cement

    Magblock Cement


    Magblock Cement (15 ml bottle with applicator tip). Will work for a few rifle or up to 15+ pistol limiters depending on amount used.
    Features:
    - Starts to set in only 1-3 minutes. Can be built up.
    - Handling strength: 5 minutes.
    - Color: Black.
    - Viscosity: paste.
    - Full Strength: 12 hours

    15 ml bottle
    $2.59
  8. FNX and FNP .40 10 round limiter for 14 round magazines.

    FNX.40 FNP.40 Magblock 10/14 (10 Round Limiter)

    FNX and FNP .40 Magblock 10 Round Limiter

    This Magblock fits the FNX and FNP .40 14 round magazines and will limit them to 10 rounds.  Easily installed in seconds under the follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

    -Simple install to make 10 round FNX and FNP .40 Magazines.

    -No modification to the magazine is required.

    -Lightweight and will not interfere with magazine reliability.

  9. Magblock 10 Round Limiter for the Sig P250. P320 and X-Five 21 round 9 mm magazines.

    Sig Sauer X-Five Magblock 10/21 Limiter (9mm)

    Sig Sauer X-Five, P320 and P250 Magblock 10 round limiter for 21 round magazines.

    This Magblock fits the Sig X-Five, P320 and P250 21 round 9 mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

    - Simple install to make 10/21 Sig Sauer X-Five, P320 and P250 magazines. 

    - No modification to the magazine is required.

    - Lightweight and will not interfere with magazine reliability.

    - Tested on factory Sig X-Five, P320 and P250 21 round magazines. The block may need to be modified to work with magazines from other manufactures.

    - This is also the same product as the P320 and P250 limiter for 21 round magazines.

    -NOTE: Universal Limiter Instructions: Use at maximum length with 25 showing in the indicator notch. Use the locking tab, but cut off the lock button for a flat base. Cement Together.

  10. Glock 10/17 Magblock 10 Round Limiter. These can be modified to fit all other Glock 9mm and .40 magazines. Pre-cut limiters available.

    Glock 19X Magblock 10/17 (9mm)

    Glock 17 and Glock 34 (9mm) Magblock

    - Fits 17 round 9mm Factory Glock 17, Glock 19X and Glock 34 magazines.  *See details on correct follower types below. 
    -Will also fit Korean Glock Magazines.  
    - Easy installation under the magazine follower.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 

    * Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
    Only compatible with the follower type shown in the pictures. 

    New patent pending design allows this limiter to be adapted to fit all other Glock 9mm and .40 magazines including a 15 round option for the Glock 17 magazine. Cutting using an appropriate tool is required. Pre-cut limiters are available.

  11. M1 Carbine 10/15

    M1_Carbine 5/15 Magblock (5 Round Limiter)

    This easy to install 5 round magblock will limit a standard 15 round M1 carbine magazine. It simply slides onto the top of the spring right under the follower. Marked on the block for correct installation. No external modifications are needed. this block will limit the magazine capacity to 5 rounds, but still allow normal magazine function and bolt operation.
  12. S&W M&P 2.0 10 round limiter installs at the base of the spring as shown. Retains use of the factory locking plate.

    Smith & Wesson M&P 2.0 9mm Compact 10/15 Magblock (10 Round Limiter)

    Smith & Wesson M&P 2.0 Compact Magblock 10/15 Limiter

    This Magblock fits the Smith & Wesson M&P 2.0 15 round 9mm magazines and will limit them to 10 rounds.   New design easily installs at the base of the spring. It is held in place with spring tension alone or can be glued or epoxied if desired. Block comes ready to install.

    *If using our Universal Limiter for this magazine: Cut to #9-10 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #9-10 will show in the limiter window notch like in the photos. 

  13. Para Ordnance 10 Round Limiter (.45) P14 10/14 Magblock

    Para Ordnance P14 .45 Magblock 10/14

    Magblock 10 Round Limiter for Para Ordnance P14 .45 magazines

    - Fits 14 round .45 Para Ordnance P14 magazines. 
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of .45. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 
    - Made of a super strong, heat resistant, fiber reinforced polymer.

  14. UZI 10/32 Mag Block

    UZI and MetalForm 10/25 Magblock

    This block will work with 25 round 9mm UZI and Metalform magazines to make a 10 round magazine. It replaces the floor plate locking tab. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.
  15. CZ Scorpion Evo Magblock 10/30 (9mm)

    CZ Scorpion Evo Magblock 10/30 (9mm)

    Magblock 10 Round Limiter for CZ Scorpion Evo (9mm) 30 Round Magazines

    - Fits 30 round 9mm CZ Scorpion Evo magazines
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 
    - Made of a super strong, heat resistant, fiber reinforced polymer.

Set Descending Direction

Grid List

Page:
  1. 3
  2. 4
  3. 5
  4. 6
  5. 7