Shopping Cart - $0.00

You have no items in your shopping cart.

 
Return to Previous Page

Magblocks

Magazine Capacity Limiters also known as Magblocks for multiple rifles and pistol magazines.

Set Descending Direction

Grid List

Page:
  1. 2
  2. 3
  3. 4
  4. 5
  5. 6
  1. Easily installed inside the spring and replaces the original locking plate.

    VEPR .308 Magblock 5, 10, and 15 Round Limiters

    Magblock for Vepr .308 20 Round Magazines.  5, 10 and 15 Round Limiters.

    Fits Vepr .308/7.62x51mm 20 round magazines made by Csspecs>

    - Easy to install in seconds.
    - Replaces the original locking plate.
    - No external magazine modifications.
    - Select 5, 10 or 15 round limiter below. 

    - Tested in Vepr magazines made by Csspecs. May fit other manufacturers with or without modification.
  2. Magblock 10 Round Limiter for Ruger P89/85

    Ruger P89 and P85 Magblock 10/15 (10 Round Limiter)

    Ruger P89 and P85 Magblock 10 Round Limiter

    This Magblock fits theRuger P89 and P85 15 round magazines and will limit them to 10 rounds of 9mm  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

    -Simple install to make 10 round Ruger P89 and P85 Magazines.

    -No external modification to the magazine is required.

    -Lightweight and will not interfere with magazine reliability.

  3. SCAR 16 10/30 limiter

    SCAR 16 Magblock 10/30 Limiter

    SCAR 16 Magblock 10/30

    - For use in the SCAR 16 FNH 30 round magazines

    - These blocks will convert a 30 round SCAR 16 magazine to hold only 10 rounds.

    - No modification to your original SCAR magazines is required to use these limiters.

    - NOTE: For use only in FNH manufactured SCAR 16 factory magazines. For regular metal AR magazines you must use the USGI limiters.

  4. Magblock 10 Round Limiter for 20 Round Sig Sauer P226 Magazines. Please see the photos to be sure your magazines are the same.

    Sig Sauer P226 Magblock 10/20 (9mm)

    Magblock 10 Round Limiter for Sig P226 20 Round Magazines

    - Fits 20 round 9mm Sig P226 US made magazines as pictured
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 
    - Made of a super strong, heat resistant, fiber reinforced polymer.

  5. CZ-75 Tactical Sport 10 round limiter for 20 round magazines. Installs at the base of the spring.

    CZ-75 Tactical 10/20 Magblock (9mm)

    CZ-75 Tactical Sport 10/20 Magblock 10 Round Limiter for 20 Round factory magazines

    This Magblock fits the CZ-75 Tactical Sport 20 round magazines will limit them to 10 rounds. Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

    - Simple install to make 10/20 CZ-75 magazines.

    - No external modification to the magazine is required.

    - Lightweight and will not interfere with magazine reliability.

    NOTE: Universal Limiter Instructions: Indicator notch should show "25" which is the maximum length, Insert the locking slide and cut the small button off so that the base is flush.

  6. Example only. The actual limiter is smaller.

    Taurus PT111 G2 Magblock 10 Round Limiter 10/12 (9mm)

    Taurus PT111 G2 Magblock 10/12 (9mm) 10 Round Limiter

    This Magblock fits the factory Taurus PT111 G2 12 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds under the follower. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus PT111 G2 magazines to 10 rounds. No external modification to the magazine is required

    Has been tested on original factory magazines.

    ***This is the same Limiter as the Sig P320 10/12 blocks and may be marked as such.***

  7. SCAR 17 Limiter being installed. Simple drop in limiter brings your 10 round magazines down to 5 rounds.

    SCAR 17 Magblock 5/10

    SCAR 17 MAGBLOCK

    - New and Improved Easy Install Design.

    - This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

    - The block attaches to the bottom of the magazine spring and will convert 10 round magazines to hold only 5 rounds, or a 20 round magazine to hold 15 rounds 

    - No modifications to your expensive FN SCAR magazines are needed to install.

    - The block can be epoxied to the spring for a permanent modification.

    - Can also limit a 20 round Scar 17 magazine to 15 rounds.

    - Made from a solid polymer. These are very strong and heat stable to over 260 degrees F.

    Same as this item:  http://www.magazineblocks.com/magento/products/magblock-kits/scar-17/scar-17-magblock-15-20.html

    *PATENT PENDING*

     

  8. Walther Creed 10/16 10 Round Limiter
  9. The 5 round limiter installs as shown. Just insert and close up the magazine.

    AR-10 ACS 5/10 Magblock (.308)

    AR10 Magblock 5/10

    Fits ACS and C-Products .308/7.62x51mm 10 round magazines and will convert them to hold only 5 rounds.

     - No need to drill any holes. 

     - Load magazines on a closed bolt.

     - Easy to install. 

    - No external magazine modifications. 

    - May fit other brand AR 10 Magazines. 

  10. PS90 Magblock 10/50

    PS90 Magblock 10/50

    PS90 MAGBLOCK  

    - New and Improved Easy Install Design.

    - This block will fit original 5.7x28mm PS90 Magazines made by FNH and some aftermarket magazines as well.

    - The block attaches to the bottom of the magazine spring and will convert 50 round magazines to hold only 10 rounds.

    - No modifications to your expensive FN PS90 magazines are needed to install.

    - The block can be epoxied to the spring for a permanent modification.

    Made from a solid polymer. These are very strong and heat stable to over 260 degrees F. 

    NOTE: Blocks are marked for 15 round fit as well.

    *PATENT PENDING*


  11. Magblock 10 round limiter for Sig P250, P320 and sig X-Five magazines. Easily convert 21 round magazines to hold only 10 rounds.

    Sig Sauer P320/P250 Magblock 10/21 Limiter (9mm)

    Magblock 10 Round Limiter for Sig P320 21 Round Magazines

    - Fits 21 round 9mm Factory Sig P320 and P250 magazines. 
    - Also works in factory Sig X-Five 21 round magazines.
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 

    - This is also the same product as the Sig X-Five limiter for 21 round magazines.

    -NOTE: Universal Limiter Instructions: Use at maximum length with 25 showing in the indicator notch. Use the locking tab, but cut off the lock button for a flat base. Cement Together.

  12. Para Ordnance 10 Round Limiter (.45) P14 10/14 Magblock

    Para Ordnance P14 .45 Magblock 10/14

    Magblock 10 Round Limiter for Para Ordnance P14 .45 magazines

    - Fits 14 round .45 Para Ordnance P14 magazines. 
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of .45. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 
    - Made of a super strong, heat resistant, fiber reinforced polymer.

  13. UZI 10/32 Mag Block

    UZI and MetalForm 10/25 Magblock

    This block will work with 25 round 9mm UZI and Metalform magazines to make a 10 round magazine. It replaces the floor plate locking tab. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.
  14. CZ Scorpion Evo Magblock 10/30 (9mm)

    CZ Scorpion Evo Magblock 10/30 (9mm)

    Magblock 10 Round Limiter for CZ Scorpion Evo (9mm) 30 Round Magazines

    - Fits 30 round 9mm CZ Scorpion Evo magazines
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 
    - Made of a super strong, heat resistant, fiber reinforced polymer.

  15. CZ Scorpion Evo Magblock 10/20 (9mm)

    CZ Scorpion Evo Magblock 10/20 (9mm)

    Magblock 10 Round Limiter for CZ Scorpion Evo (9mm) 20 Round Magazines

    - Fits 20 round 9mm CZ Scorpion Evo magazines
    - Easy installation at the base of the spring.
    - Limits the magazine to 10 rounds of 9mm. 
    - Held in place with spring tension or can be epoxied for a permanent modification. 
    - Lightweight, efficient design. 
    - Made of a super strong, heat resistant, fiber reinforced polymer.

Set Descending Direction

Grid List

Page:
  1. 2
  2. 3
  3. 4
  4. 5
  5. 6