Shopping Cart - $0.00

You have no items in your shopping cart.

 
Return to Previous Page

Products

Set Ascending Direction

Grid List

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  1. HK33/ C93 10/40 Magblock. See the other photo for installation of the locking plate insert.

    HK33 C93 10/40 Block

    HK33 and C93

    - This block will convert 40 round HK magazines into a 10 round magazine.

    - Works with H&K .223/5.56mm magazines.

    - Includes small insert for the locking plate. This gives the block a flat surface to make contact with. 

    $6.49
  2. Our Magblock for Thermold 20 round AR magazines replaces the original locking plte and have a built in floor plate locking tab.

    Thermold 10/20 Magblock

    Magblock 10/20 MCL (Magazine Capacity Limiter) for Thermold 20 round AR-15/M16 Magazines.

    -Fits Thermold 20 round black Zytel Nylon magazines in 5.56 mm, 223 Cal.

    -Will convert a 20 round magazine to hold only 10 rounds.

    -Only fits current production Thermold magazines. Has not been tested on older versions. Some modification may be needed for older production magazines. 

  3. 15 Round Limiter for 30 Round Thermold Magazines. This easy to install limiter attaches to the bottom of the spring. The floor plate is then installed normally.

    Thermold 15/30 Magblock

    Magblock 15/30 MCL (15 Round Magazine Capacity Limiter) for Thermold 30 round AR-15/M16 Magazines.

    - Fits Thermold 30 round black Zytel Nylon magazines in 5.56 mm, 223 Cal.
    - Will convert a 30 round magazine to hold 15 rounds.
    Fits current production Thermold magazines as seen in the photos.
    - Easy install using all of the original magazine components. 
  4. 10 Round Limiter for the Mini 14 magazines made by Tapco. Easy to install at the bottom of the spring and replaces the Tapco locking plate which is not shown.

    Mini 14 MCL 10/30 Block (Tapco)

    Mini 14 Magblock 10/30 MCL - Magazine Capacity Limiter for Tapco 30 Round .223/5.56mm Magazines) 

     - Fits new Tapco 30 round magazines for the  Ruger Mini 14. 
    - These blocks will attach to the bottom of the spring.
    - Converts a 30 round magazine to hold only 10 rounds. 

    *Only for use in TAPCO Mini 14 magazines.

     

  5. 15 Round Limiter for ArmaLite 25 Round Magazine

    AR10 ArmaLite Magblock (.308) 10/25 and 15/25 Limiter

    Magblock for ArmaLite AR10 25 Round Magazines.  10 and 15 Round Limiters.

    Fits ArmaLite AR10  .308/7.62x51mm 25 round magazines and will convert them to hold only 10 or 15 rounds.

    - Easy to install in seconds.
    - No need to drill any holes.
    - Load magazines on a closed bolt in most rifles.
    - No external magazine modifications.
    - Select 10 or 15 round limiter below. 

  6. Magblock 10 Round Limiter for ProMag DPMS LR-308. Easy to install. The spring fits into the hole in the block to prevent movement and noise.

    ProMag DPMS LR-308 Magblock 10 and 15 Round Limiters

    Magblock for ProMag DPMS LR-308 20 Round Magazines.  10 or 15 Round Limiters available.
    Fits Promag DPMS LR-308 20 round magazines in .308/7.62x51mm and will convert them to hold only 10 or 15 rounds.

    - Easy to install in seconds.
    - No need to drill any holes.
    - Load magazines on a closed bolt in most rifles.
    - No external magazine modifications.

  7. Mini 14 10/20 Magazine Block for Promag Only

    Mini 14 Magblock 10 and 15 Round Limiters (Ruger)

    Mini 14 Magblock 10/20 MCL (Magazine Capacity Limiter for Ruger Magazines

     This block is for use in RUGER 20 round Mini 14 magazines. These blocks will attach to the lower spring and convert a 20 round magazine to hold only 10 or 15 rounds. (Select option below). 

    - Only for use in RUGER manufactured magazines. 

    - This is a modified USGI magblock.

  8. HK416 22LR 10 round limiter. Works with the pictured magazines.

    HK416 22LR 10/30 Magblock

    HK416 22LR 10/30 Magblock 10 Round Limiter

    - This block will convert 30 round HK 416 22LR magazines into a 10 round magazine.

    - Easy to install without damage to your magazines.

  9. MPA 10 Round Limiter

    Masterpiece Arms MPA 10/32 Magblock 9mm (Tapco)

    10 Round Limiter for 32 Round Tapco MPA Magazines

    Magblock 10/32 Magazine Capacity Limiter for the Masterpiece Arms 32 round 9mm magazines made by Tapco.

    - This block will replace the lower spring attachment point or locking plate and convert a 32 round magazine to hold only 10 rounds.

    - Very easy to install

    - Does not affect reliability.

    - No increase in spring pressure.

    - Slight modification of the follower is required to fit all 10 rounds. Please see the pictures posted here for instructions.

  10. SCAR 16 10/30 limiter

    SCAR 16 Magblock 10/30 Limiter

    SCAR 16 Magblock 10/30

    - For use in the SCAR 16 FNH 30 round magazines

    - These blocks will convert a 30 round SCAR 16 magazine to hold only 10 rounds.

    - No modification to your original SCAR magazines is required to use these limiters.

    - NOTE: For use only in FNH manufactured SCAR 16 factory magazines. For regular metal AR magazines you must use the USGI limiters.

  11. Pmag Ranger Plate .223 Gen M3

    Pmag Ranger Plate .223 Black- Gen M3

    For use with Magpul Pmag Gen M3

    Gen M3 Magpul PMAG Ranger Plate

    This is a floorplate replacement for the 5.56x45 PMAG Gen M3 that incorporates an integral loop similar to the original Magpul USGI Ranger.

    When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and control during high stress, tactical magazine changes.

    Fits Gen M3 Pmags only in 10, 20, and 30 round sizes.

    $5.95
  12. Promag 10/30 Magblock for Polymer magazines.

    Steyr AUG 10/30 Magblock 10 Round Limiter

    10 Round Limiter for Steyr AUG 30 Round Polymer Magazines

    Magblock 10/30 MCL (Magazine Capacity Limiter) for Steyr AUG 30 round polymer magazines in .223/5.56mm.

    - This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.

    - Customized base of the Magblock includes two locking points just like the original locking plate.

    - Does not affect reliability.

    - No increase in spring pressure.

  13. 10 Round Limiter for 30 Round E-Lander Magazines.

    E-Lander 10/30 Magblock 10 Round Limiter

    E-Lander Magblock 10/30 Magazine Capacity Limiter (10 Round Limiter)

    - For use in E-Lander 30 round magazines.
    - These blocks will convert a 30 round E-Lander magazine to hold only 10 rounds. 
    - Replaces the E-Lander locking plate and has a built in floor plate lock.  

    - These can be used with USGI Ranger Plates and L-Plates. The bottom of the limiter can be modified for this and the block shortened by 2mm to allow room for the Magpul locking plate. We offer this as an option. You can also do it yourself following the instuctions found in the FAQ section here: http://www.magazineblocks.com/magento/faq  FYI: Once the block is modified for use with a Ranger Plate or L-Plate the block can not be used without one of these products in place ot it will hold >10 rounds. 

  14. Sale
    Magblock Gen M3 15 Round Limiter for 20 Round Magazines.

    GEN M3 Pmag MCL 15/20 Block (15 Round Limiter)

    15 Round Limiter for Gen M3 20 Round Pmags

    Magblock 15/20 MCL (Magazine Capacity Limiter) for Magpul 20 round Gen M3 (curved) Pmags in .223/5.56mm. 

    - This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 15 rounds.

    - The Pmag dust covers will still fit when loaded.

    - Does not affect reliability.

    - No increase in spring pressure. 

    - Compatable with new Magpul Gen 3 Pmags only.  These will not work in original Pmags.

    Regular Price: $6.25

    Special Price $4.95

    As low as: $3.95
  15. SCAR 17 Magblock 10 round limiter for Thermold magazines. New easy to install design.

    SCAR 17 and RRA LAR-8 Magblock 10/20 for THERMOLD

    SCAR 17 MAGBLOCK for THERMOLD 20 Round. Also fits Rock River Arms LAR-8 Polymer Magazines.

    - This block will fit 7.62x51mm NATO/.308 SCAR 17 and LAR-8 Magazines made by THERMOLD and RRA ONLY. 

    - The block attaches to the bottom of the magazine spring and will convert 20 round magazines to hold only 10 rounds.

    - No modifications to your expensive FN SCAR magazines are needed to install.

    - The block can be epoxied to the spring for a permanent modification.

    Made from a solid polymer. These are very strong and heat stable to over 260 degrees F.  New easy to install design with spring catch.

    *PATENT PENDING*

    NOTE: The 10 th round may fit a little tighter in the RRA magazines, and need to be loaded with the bolt open. You can always custom fit the limiter if desired.

Set Ascending Direction

Grid List

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5